- Can you rewet Thinset?
- How do you dissolve hardened concrete?
- What happens if Thinset is too thick?
- How long does Thinset need to set?
- Which is better thinset or mastic?
- Do you have to remove old mortar before laying tile?
- Do you have to remove old tile adhesive before tiling?
- What will dissolve Thinset?
- What happens if Thinset gets wet?
- Can I add water to thinset?
- Can you mix thinset mortar by hand?
- How do you break concrete without a jackhammer?
- How can I make Thinset dry faster?
- Does vinegar dissolve concrete?
- Will sugar water dissolve concrete?
- Can I put new mortar over old mortar?
- Can I put Thinset over old Thinset?
- How thick should thinset mortar be?
Can you rewet Thinset?
There is no way to save mixed thinset.
Thinset cointains portland cement, which chemically reacts with the water you add to harden.
It does not dry by evaporation, so if you mix up a batch of thinset and pack it in an air-tight container, it will still harden in a few hours..
How do you dissolve hardened concrete?
Spread your phosphoric acid or trisodium phosphate over the concrete area you want to clean first, using a mixture with water that’s recommended by the individual manufacturer. Use a brush to scrub the acid into the concrete. These are weaker acids that just might work to dissolve a sufficient amount of concrete.
What happens if Thinset is too thick?
The most likely dangers of using it too thick are cracks (see photo), delamination, and lippage. Please note that the thinset being shown as a patch in the previous pictures is one designed to be used on plywood (an ANSI A118. 11 mortar). If you try to do that with an el-cheapo thinset, good luck.
How long does Thinset need to set?
24 to 48 Hours You should wait at least 24 hours before grouting the tiles. You may notice that the edges of the thinset or the thinset showing through the grout lines looks dry. Don’t be fooled by this. The thinset under the tiles isn’t receiving as much air as the edges and is therefor not fully cured.
Which is better thinset or mastic?
Thinset is a stronger material than mastic, making it a better choice for horizontal applications such as flooring that get a lot of pounding. Dry-mix thinset is inexpensive and easy to use.
Do you have to remove old mortar before laying tile?
You can put tile over old thinset. Make sure it not loose, vacuum to remove any debris, check for cracks, apply membrane if needed. I’ve done it hundreds of times for fifteen years including my own five houses. Remove the old thinset to get a flat surface for wood or laminate installation.
Do you have to remove old tile adhesive before tiling?
You don’t need to remove the old adhesive as long as its not loose at all. Wouldn’t recommended the scrapper that your using, it’ll dig in too much, use a normal decorating scrapper if you can to remove any loose adhesive and get it as flat as possible.
What will dissolve Thinset?
If not, pour some more boiling water over it to loosen it. You can also use a masonry chisel that is the same width. Continue removing the thinset in small chunks until you’ve removed enough to accommodate your new tiles. Always use a putty knife with a hammer-end handle and sharp blade.
What happens if Thinset gets wet?
The spilled water does put an additional temporary moisture load on any wooden substructure, but again, this would be negligible in light of the original water content of the mortar.
Can I add water to thinset?
If it’s hot and dry where you’re working, use COLD water to mix the thinset. … If you add water to stiff thinset to make it workable, you break the microscopic Portland cement crystals and the thinset will NOT be as strong as it could be. This is why you only mix as much as you can use in a short time.
Can you mix thinset mortar by hand?
1 Mix the thinset mortar. If you are tiling a countertop or the floor of a small to medium-sized room, you can mix the mortar by hand. A square-notch trowel is the best tool for the job. Add a couple of inches of liquid to the bottom of a 5-gallon bucket and then pour in some powder.
How do you break concrete without a jackhammer?
Here’s a few tips:Recruit a buddy to lift a corner with a pry bar. Start slamming at the corners and work your way towards the center.Pry and pull out the broken chunks as they break apart.Don’t hit the same spot twice. Keep moving and keep lifting with that pry bar.
How can I make Thinset dry faster?
Strategies for doing this involve hastening evaporation of the water.Use less water when you mix the mortar. … Spread the mortar on a dry substrate. … Heat the surrounding environment with a room heater, or direct the heat towards the mortar.More items…
Does vinegar dissolve concrete?
Vinegar will dissolve concrete – but will take a LOT of contact time as vinegar is a mild acid. I can’t see using vinegar to remove this even if it is concrete, because almost all of it would just flow on by – you have no way of making it sit at the concrete to dissolve the cement.
Will sugar water dissolve concrete?
Dry sugar has no effect on hardened concrete, but sugar solutions can be very corrosive.” … The concrete typically begins to soften in 20 to 30 minutes, at which point you should rinse it off with water.
Can I put new mortar over old mortar?
Applying fresh mortar on top of old mortar that is loose or falling out will do little or no good; enough of the old mortar must be removed to make room for a layer of new mortar that is at least half an inch thick, and even then it is important to make sure that what is left of the old mortar is still solid and …
Can I put Thinset over old Thinset?
Tile needs a smooth, level surface to be installed on. You can put new thinset on top of old, but only if the old thinset is perfectly smooth and level. … The best option to smooth out the old thinset and prepare it for new tiles is to grind it down.
How thick should thinset mortar be?
3/16th inchThe terms thinset cement, thinset mortar, dryset mortar, and drybond mortar are synonymous. This type of cement is designed to adhere well in a thin layer – typically not greater than 3/16th thick. For example, a 3/8″ notch trowel will produce a 3/16th inch thick coating after the tiles are pressed in to the cement.